Posts
General Product Question posted February 10, 2017 by Alex ShusterQuestion:I have a 360bt leaf blower and i'm not sure if the choke should be in the ON position all the time once its started. Should I close the choke after 30 minutes of use or until its warmed up? I tried closing it several times and each time it shuts of. Is this normal? When should the choke be turned off?- General Product Question posted July 13, 2011 by Jean HoenningerQuestion:Hi, I would like to purchase a gutter cleaning accessory kit for our Husqvarna 125 bv backpak blower. Have found the kit, but it gives specific models that it is to be used with - - one of those is the 125 b series. My question may seem silly, but it's quite serious. Is the 125 bv blower part of the 125 b series? I would like to be certain about this BEFORE i purchase the accessory kit, but I can't seem to find anything that connects the 125 BV with the 125 b series. Thanks in advance to anyone who might clear this up for me.
- General Product Question posted December 8, 2011 by Mark MayerQuestion:How do I remove the vacuum tube once its been installed on a 125BVx blower to return to normal operation? The the tube has 4 snap fit tabs, and once these are engaged I cant figure out how to rotate to the unlock position and remove the tube.
- General Product Question posted December 2, 2018 by robert pattersonQuestion:I have a 125b blower,changed coil,gapped with a business card,changed all fuel lines,cleaned carb.If you can pull long enough it might crank.when it does it runs good. What could cause this? coilgap maybe?
- General Product Question posted November 3, 2018 by Dan HarrisonQuestion:I just purchased a 150BT blower. It starts great but dies when I take it off choke, even after 30 minutes of operation. I know it is not performing at 100% on choke. What can I do? Thanks!
- General Product Question posted October 26, 2018 by Dale BeckmannQuestion:I just bought a 125bvx blower today. While I was filling out the registration, I had to upload a pic of the receipt to qualify for the extended warranty.
As I was doing this, I got an email from Husky CONFIRMING MY UNFINISHED REGISTRATION!! WTF!!!
You people already got my money. You can't wait for me to finish registering it. Now, you want me to mail in the receipt? I don't think so.
I go to the website to try find this contact page, and spend close to a hour going from one useless FAQ to another.
But I can't even do this until I "finish registering the blower" and open an account.
I wouldn't characterize this as "customer service"
I haven't even put gas in it yet and I'm ready to take it back to the store, who by the way had 23 different leaf blowers to choose from. I'm pretty sure I could find a manufacturer that made it a little easier to contact cust. svs.
Now that I've shared my first experience with Husqvarna, could someone please tell me how I can email the rest of my product information so I can complete the registration.
I would greatly appreciate it.
Thank you
Dale Beckmann - General Product Question posted June 14, 2018 by Jean MalloryQuestion:I have the 350BT and it just started stalling after I accelerate. It idles & starts fine, but as soon as I accelerate it dies. I've seen others ask this question but I didn't see any answers.
- General Product Question posted March 27, 2018 by Matthew BrousseauQuestion:350BT: Is this gap in the housing normal?
- General Product Question posted November 27, 2017 by Adam WiggershausQuestion:I bought a 125BVX blower/mulcher in June of this year, used it through the summer worked great. Went to fire it up to blow leaves this fall could not get it to start at all. I always followed the start up steps, a little frustrated as to why this unit has quit. Need direction as to how to proceed.
Thank you
Adam - General Product Question posted October 28, 2017 by Charles FrahmeQuestion:New 125B Leaf Blower:
I'm very confused about the function and operation of the "speed control" ("cruise control") on my blower.
I can find no reference in the manual on how to use this thumb operated control switch.
The one on my blower seems to have two positions: fully CCW or fully CW. Any setting in the middle and the control just slides to the CCW position.
Please help!
Detailed information much appreciated.
Thanks!