Posts
General Product Question posted October 9, 2011 by Steve KQuestion:150BT vs. 350BT--When someone else recently asked what is the difference between these two blowers, the answer given was
>>The primary differences were shrouding, decals and the blower tubes / nozzles.<<
I am considering purchase of these models. However, the answer didn't really make it clear what the differences are. My questions are:
--In saying that the differences "were," do you mean that one of these models has been discontinued? If so, which one?
--What are the differences in the shrouding and the blower tubes/nozzles, and what is their effect when you are using these models?
--Why do these two models have different cfm and air speed ratings?
--Which model is better, and why?
Thank you very much.- General Product Question posted November 6, 2011 by David MQuestion:I filled out online registration form for the promotional backpack blower tee shirt. This was about two months ago. I was wondering how long does this normally take?
- General Product Question posted December 8, 2011 by Mark MayerQuestion:How do I remove the vacuum tube once its been installed on a 125BVx blower to return to normal operation? The the tube has 4 snap fit tabs, and once these are engaged I cant figure out how to rotate to the unlock position and remove the tube.
- General Product Question posted July 10, 2012 by Terry PelkeyQuestion:I read the post about the back pack blower t-shirt and didn’t see a positive answer so I’ll ask again. I purchased a 350BT blower in April of 2012 and I believe the t-shirt was still being given away with them after you register the blower. I'm trying to find out how long that was going on for. I have purchased 2 chainsaws and the blower and have missed out on all the promos that Husqvarna has had…
Thank you,
Terry Pelkey - General Product Question posted February 10, 2017 by Alex ShusterQuestion:I have a 360bt leaf blower and i'm not sure if the choke should be in the ON position all the time once its started. Should I close the choke after 30 minutes of use or until its warmed up? I tried closing it several times and each time it shuts of. Is this normal? When should the choke be turned off?
- General Product Question posted October 25, 2017 by Jody YocomQuestion:I have a 125b leaf blower that will not start. I started with the fuel lines and filter that were no good and replaced all, I have replaced the carburetor after cleaning the old one just to make sure, I have replaced the spark plug gapped .020(3 times) and coil, replaced the kill switch (disconnected the kill switch), removed the flywheel to check key for timing purpose, I purchased a spark tester to make sure that I was getting spark, checked compression it was 94 after 5 or 6 pulls. The blower will not hit at all. What am I missing.
- General Product Question posted October 11, 2013 by me meQuestion:What are the EXACT differences between the 150bt & 350bt?
General Product Question posted November 6, 2011 by James BQuestion:I purchased a 350BT about a month ago and used it for the first time. Every time I tried to open the choke, the engine stalled. I cleaned my yard on half-choke and then I began to wonder if the choke sticker was upside down. The choke sticker had "closed" at the top and "open" at the bottom (the text was upside down). Am I correct that the sticker was incorrectly placed upside down at the factory? Thus, is "UP" open and "DOWN" closed?- General Product Question posted December 26, 2014 by Ed FariasQuestion:Correction .... Correction .... Correction
My post on "Hard Start" is in referrence to my new "350BT" and not the 130BT which I listed in error. Am still looking for the "Decompression Valve" which is supposted to making starting easier. - General Product Question posted December 26, 2014 by Ed FariasQuestion:My new 130BT requires a "hard pull" to override the compression at start/up. Where is the compression relief valve located on the engine and can it possibly be stuck shut requiring the "hard pull". I only have one hour use of the unit....can I expect the compresson relief valve to start working after several stop/starts?