Posts
Service & Maintenance Question posted August 21, 2012 by J MattesI have DRT900 that I purchased at the end of March. I am having issues with the shifting on the tiller. The gears no longer align with the shift indicator. Also I cannot get the tiller in reverse anymore. As you are shifting the forward and reverse till lock in way to the left. The middle portion is just very loose and the far right will get me into forward and neutral. Any idea what the issue maybe. I didn't want to tear into the transmission if it is under warranty.- Service & Maintenance Question posted October 4, 2012 by Raymond PipitoneJust got my new FT900 tiller. It started on the first pull. After several minutes of running the idle became very rough. The only way it runs smoothly is if I choke it half way. Is the rough running normal, or does it need some type of service or adjustment?
Thank you! - Service & Maintenance Question posted June 7, 2013 by Ken TheisBrand new DRT900H tiller. Put it together runs great on idle or moving it to the Garden. I can engage the tines in the air and still runs good. As soon as I drop it in the groud,under load the engine surges constantly and consistantly. No change in the RPMs as it hits harder or softer soil. The machine bounces forward and back. This can't be normal? Somewhat hard to handle when tilling. Locale dealer is working on it and can't seem to figure it out. Replaced Carborator, he feels that it is not normal but is it a characteristic of the tines or this machine? Anybody have the same problem?
- Service & Maintenance Question posted February 14, 2014 by tim mccormackHello I have a crt 900 tiller, getting it ready for the season it says to lube gear box with EP#1 grease?
Will Mobile CM grease,extreme pressure, NLGI 1 lithium complex gray temp range -30 deg to 175 deg c dropping point 260 degree c
item from granger, item number 4nyy5, - Service & Maintenance Question posted June 5, 2014 by Gordon HandfordHusqvarna CRT52 rototiller: how much packing grease should you put into the transmission when repairing it?
- Service & Maintenance Question posted October 28, 2013 by Randy McCormickI bought a DRT900H tiller 3 months ago. It has about 10 hours use to date. It is very difficult to shift into gear. In addition, the transmission makes a grinding/scraping noise, even when I push the unit forward with the transmission in neutral with the engine off. Based on the number of complaints I have seen on the web, is there something fundamentally wrong with the design of the transmission in this unit? Has there ever been a recall to fix this problem?
- Service & Maintenance Question posted April 19, 2013 by Armand BeaudryI am looking for a service manual for a CRT 51 tiller Model # 954001092B. The bearing,shaft ground drive L.H. and R.H part number (532143009 and 532143008) need replacing.
- Service & Maintenance Question posted November 11, 2012 by Bill PartnerFuel switch location? I just purchased the. DRT900H tiller. It was a return and fully serviced before I purchased it. But I cannot get it to start. The manual I downloaded from the Husqvarna site is for a 2009-2012 models. I have the 2012. The start up directions say to Push fuel valve to “ON” position and Turn engine switch to “ON” position. I cannot locate either of these switches on the tiller or in diagram provided in the manual. I know it seems like a silly question but can someone tell me where these are? I can start the tiller If I pour gas in carburetor but it only runs for a second. I am guessing if there us a fuel switch it is set to off. Any help would be appreciated
- Service & Maintenance Question posted July 18, 2013 by Janet MeissnerI have a brand new Husqvarna 900 rototiller that I have used twice (less than two hours). The second time I used the machine it started forward and/or reverse motion (depending on the gear I selected) regardless of whether I had the tine control depressed to the handle of the machine or not. Previously, forward or reverse movement would only occur (as explained in the operator's manual) when the tine control handle was engaged (held to the handle). Do you have any trouble shooting ideas? This is the 2nd machine as the first one wore a hole through the guard and belt broke with less than an hour operation. I hope you can get Husqvarna and myself back on track to a satisfied customer relationship. Thanks!
- Service & Maintenance Question posted April 22, 2013 by Larry FortsonI have a Husqvarna rear tine tiller. While tilling by neighbors garden I hit a tree root. The gears all work but the tines will not turn. I took it to a repair shop. and was told that the transmission was broken and would cost around $700. it would be cheaper to buy another one from him. My question is that I checked the tiller and it would go into forward and reverse with out any problem. If this is the case how can the transmission be broken. He also told me on the phone that maybe the chain was broken.