Posts
Parts Question posted May 5, 2017 by James FrancisQuestion:Well, here's a question for the old timers..
I can't find a tap feed string head that will fit my Father in law's 25R trimmer (Nippon Kreis) that still runs beautifully. I've tried a bunch of universal ones, none worked. Can someone here steer me in the right direction/brand/part number? My dealer came up with some possibilities, but didn't want to order 6 of them to see if it would fit.
Thanks,
Jim- Parts Question posted September 26, 2016 by David CalkinQuestion:I own a 225LD trimmer and needed a new trimmer head so I looked it up on your website and decided to buy the T35X which listed the 225LD as a model that it would fit. I looked up the dealer from your web site which is John H. Eschenberg Inc. and ordered it from them. After bringing it home and trying to install it, it was clear that it does not fit the 225LD. The screw hole on the T35X is much larger than the screw of the trimmer. How do I resolve this?
- Parts Question posted July 2, 2016 by Curtis BohananQuestion:Recently purchased a model 223R trimmer with brush cutter blade. Nut and washer for securing blade is missing. Dealer does not have. Am t
having hard time finding lock nut the that matches size and thread count. Can you provide me with nut size and thread count so hopefully I can find. Thanks/ - Parts Question posted March 23, 2016 by Christopher CattoQuestion:Where can I purchase a trimmer attachment for a 128LD?
- Parts Question posted September 10, 2015 by Charlie YarwoodQuestion:After failing to find the info I need at husqvarna.com, I came to AnswerArmy. I've found several posts that state which brush cutter attachments DO NOT work with 128LD, but no info on ones that DO work. Is there a brush cutter attachment that works with 128LD?
Thanks,
C Yarwood - Parts Question posted May 2, 2012 by Sean CoakleyQuestion:I have a Husqvarna 128CD. The trimmer head popped off. I ordered a T25 head to replace it and found that the dust cup apparently came off as well. The threaded screw at the end of the shaft is of a much smaller diameter than the T25 head so I'm not sure a dust cup would even make a difference in attaching the head. In any event I am having a hard time finding this dust cup part at any of your dealers.
I have attached a picture of the tag on the unit. As you can see it is scratched so I can't figure out what exactly the SN is.
Can you help me or am I going to replace this with a non-Husqvarna unit? - Parts Question posted July 1, 2017 by Gary RicheyQuestion:129LK string trimmer: Husqvarna website shows 2 spare parts lists for this model, each with a different part # for the trimmer head? 537338306 isn't correct as the shaft diameter is too large on the one I purchased. Is 578446101 correct?
- Parts Question posted August 30, 2016 by Jeff HaughtQuestion:I have a 128LD trimmer and it will not idle. It runs good and cuts fine but it will not idle. I've rebuilt the carb, replaced the fuel lin and will start easy if I hold the throttle wide open. What can I do to get it to idle?
- Parts Question posted December 7, 2015 by Theresa HarperQuestion:I have a Husqvarna Trimmer model #225R. I need to purchase a piston assembly, part #503859702, and it can't be found anywhere. I called the customer service number but the connection was so bad that I could only make out that it was out of stock. (the direct line phone number did not work either.) I need to know if there's a compatible part for the trimmer, if there will be none available ever. This has been a frustrating search. Please help.
- Parts Question posted October 30, 2015 by Brandon WilliamsQuestion:My Husqvarna 128CD string trimmer had its bump knob break (and therefore the bump spring inside it).
Is this possible to replace alone?
I found a couple of parts, the bump knob and spring, are these the correct parts for the 128CD?
Husqvarna String Trimmer Bump Knob 537419601
Husqvarna String Trimmer Bump Knob Spring 530053241