Posts
Service & Maintenance Question posted August 4, 2018 by Michael SefsikQuestion:I need a diagram of how the drive belt is routed and how the drive idler pully tension spring is connected- Service & Maintenance Question posted July 16, 2018 by John owensQuestion:I've got a zero turn MZ6128 mower that has a continuous oil leak from the bottom. We have changed all deals, housing and gaskets several times ...still leaks.
Please please help. I'm having to pay someone to mow my grass
Thanks - Service & Maintenance Question posted July 11, 2018 by Ernest CampbellQuestion:I recently purchased a Z254F zero turn mower and would like to buy a set of replacement blades. However searching (even on the Husqvarna site)for 582760501 (the PN listed in the Parts Manual) gives no results even on the Husqvarna site. These are 18-1/4" blades. Where can I purchase a set?
- Service & Maintenance Question posted July 8, 2018 by Ronald CoxQuestion:Oil on electric MagStop Clutch/BrakeDetails:
My Husquvarna CZ4817 lost 3 engine mounting bolts causing a slight rotation of engine on mower deck. This slight rotation caused the oil drain tube (tube with 90 degree elbow hanging down into the hole in the deck) to start hitting the edge of hole because of engine vibrations. (I do not know how long this has been happening but I have a series of issues which I am trying to rectify;) The vibrations led to the oil drain tube from the engine to actually break while I had the engine running just to check on another problem (overheating and shutting off?) Ran engine at high speed about 15 minutes - all ok. Then went to lower speed and wanted to actually drive mower to see if it shuts down again. That is when I noticed engine oil all over mower deck and floor. Was able to get remaining threads from oil drain pipe out and inserted new pipe.
Problem: Oil ran all over mower deck and ran thru deck holes onto the electric clutch. I know oil on a clutch does not work. Took a screwdriver and paper towel into space where clutch is and was wiping oil from the clutch surfaces. Wanted to remove clutch and hand clean better. Can you spray solvent/alchol of some type to clean clutch surface? Could not get clutch off so how do you do this? In case I have to buy a new clutch. Could not get crescent wrench on ring with the flat sides while trying to unloosen attaching bolt.
Thanks for your time.
- Service & Maintenance Question posted July 7, 2018 by Victor CogginsQuestion:I just purchased a MZ54 and I
over greased the front wheel mount and the cap popped off. I was able to put it back on. My question is do you think this did any damage.
Thanks,
Victor - Service & Maintenance Question posted June 23, 2018 by william andersonQuestion:I need to see what I need to do in order to change the motion belt, not the blade belt. RZ 4623 with Kohler engine.
- Service & Maintenance Question posted June 22, 2018 by richard brackQuestion:Q1 Is the PTO Sx (labeled on the schematic) on an RZ4619 actually the blade control sx?
Q2 On the RZ4619, the schematic shows a "solenoid" and an "electric clutch." I assume the electric clutch (in the lower left corner of the pictorial) is the blade control clutch just under the engine. What is the "solenoid" (in the upper left corner) and what does it control?
Q3 The schematic says the "seat unoccupied" for the drawing, but the drawing shows the seat sx to be in the closed position. Are both items correct? Is the seat sx closed if the seat is unoccupied?Details:The questions come from page 58 on my Operator Manual for the RZ4619. This manual is part number 115 127127 IR, dated 10-15-08.
- Service & Maintenance Question posted June 21, 2018 by David TaylorQuestion:I recently bought a Z254F w/KT745 Koehler engine. I would like to buy a service repair manual for the ZTR and engine. I have my own repair shop (auto) and intend to do the regular maintenance and repairs within my shop as needed. Can you help me acquire the manuals?
Regards,
David Taylor - Service & Maintenance Question posted June 21, 2018 by Kathy BrojakowskiQuestion:We own a Husqvarna rz46i with the SmartSwitch ignition. This morning when I tried to start the mower the switch literally caught fire and smoked until we were able to remove the battery cable.
The replacement is $300. The problem is the cost of a new switch and the fact that we have no idea why the switch blew up. The mower is 4 years old so no warranty.
We'd love to put a keyed switch on it but with all of the safeties we're sure that won't work.
Any diagnostics we should do to see if the failure was caused by something other than a faulty switch? Husband says the ignition solenoid it working.
ThanksPhoto:
- Service & Maintenance Question posted June 13, 2018 by Danny ArmandQuestion:I have a 2015 Husqvarna Z248F. Does anyone know what the Iso-Mount Bushing is? The location on the deck is odd and I can't figure out what its there for. Mine split on one side and came off the bolt. I will replace it but I would like to know what it does.
Filter by Date
| S | M | T | W | T | F | S |
|---|---|---|---|---|---|---|
| 1 | 2 | |||||
| 3 | 4 | 5 | 6 | 7 | 8 | 9 |
| 10 | 11 | 12 | 13 | 14 | 15 | 16 |
| 17 | 18 | 19 | 20 | 21 | 22 | 23 |
| 24 | 25 | 26 | 27 | 28 | 29 | 30 |
| 31 |