Posts
Parts Question posted June 3, 2013 by Ed ReznyQuestion:"Adjustment Screw" for Husqvarna 316 Electric chainsaw: The "adjustment screw" (as described in the manual's write-up below) on my 316 electric chainsaw snapped recently, but I cannot figure out the number of the part to order. The parts information I've seen online generally lists a number of screws that can be ordered, but not one specifically described below as the adjustment screw. Can you help me determine this? Thanks.
"Seat the guide bar on the adjusting pin and replace the clutch cover. Check that the drive links fit correctly on the drive sprocket and that the chain is in the groove on the bar.
Tighten bar nuts finger tight. Adjust chain tension, using
combination wrench to turn adjustment screw clockwise to
tighten. Tighten adjustment screw until the chain is drawn
snugly against the underside of the bar."- Parts Question posted February 11, 2012 by Joey JoejoeQuestion:16" bar for a 455 Rancher?
I'd like to buy a Rancher 455 20" saw as it looks like a reasonably priced saw that can handle a 20" bar. But at the same time I'd like to be able to switch to a smaller 16" bar when I don't need the 20" length. But I'm surprised that I can't seem to find a 16" bar for the 455. I would think (naively perhaps) that I could find a bar from 14 to 24" to easily fit most of these saws. Is that not true? If not true, why aren't these bars more interchangeable?
Thanks - 3120XP Ignition and carb question.escalatedParts Question posted January 9, 2014 by JPQuestion:3120XP Ignition and carb question.
- Parts Question posted December 21, 2015 by Eugene Rounds
Question:338xpt Fuel tank vent valve PN number needed see image for location. - Parts Question posted July 3, 2014 by Eric GroenendykQuestion:450 CHAIN OIL LEAK
My 450 leaks out all it's chain oil when stored. I saw a post from 2011 concerning a oil leak issue for a rancher 455 with similar issues as mine. The response listed parts to replace. Are the parts the same for the 450 & 455?
Specifically the post listed #537 40 35 01 plug & #530 02 61 19 duck bill check valve. Are these the same for my 450? - Parts Question posted December 18, 2015 by keith olsonQuestion:460 Rancher replacement chain
- Parts Question posted August 24, 2016 by Bob CardenQuestion:550XP Blown Transfer Port Gasket
- 576xp crank bearings.escalatedParts Question posted June 3, 2013 by Ro BoQuestion:576xp crank bearings.
- Parts Question posted October 12, 2011 by Dave RasmussenQuestion:Are Chain Saw Models (Husqvarna) 450 and 450e the same saw but the 450 has a manual chain tension adjustment, but the 450e has a automatic chain tensioning design ? IAll other parts such as spark plugs, air filter and fuel filter are the same ? Is their a pdf type file listing Model 450 parts ? What type of Husqyarna 2 Cycle Oil should I use (the Premium synthetic blend with fuel stailizer/Low Smoke Formulatio or the XP Professional Performance 2 Cycle Oil ? Those two part numbers might be 578820100 and the other number might be your 578820086 !!!
Thanks For Any Assistance - Parts Question posted December 1, 2011 by Richard MulhollandQuestion:Based on your answer to my previous question concerning my 350 chainsaw with the following tag info,
Husqvarna 350
967 01 18-00
S/N 05 0900904
I began looking for the parts I need in the 350 (2005-05) manual. The parts that are shown in the illustrations show two different part numbers one for a 350 and one for a 350EPA. My saw has the heat deflection shield that is shown with only an EPA part number. This info begs the question; What parts do I purchase for my saw the ones with just the 350 designation or the ones with the 350EPA designation? I need an answer so I can order the correct parts. Thank you.
Filter by Type
Filter by Tag
- All
- 235
- 235 e-series
- 240 e-series
- 3120 XP®
- 316 e-series
- 334T
- 338 XP® T
- 339 XP®
- 346 XP®
- 346 XP® E-TECH® TrioBrake™
- 346 XP® G
- 350
- 353G E-TECH®
- 357 XP®
- 357 XP® G
- 359
- 372 XP® W
- 385 XP®
- 385 XP® G
- 385 XP® W
- 390 XP®
- 390 XP® G
- 390 XP® W
- 395 XP®
- 395 XP® G
- 395 XP® W
- 435
- 440 e-series
- 445
- 445 e-series
- 450
- 450 50th Anniversary Edition
- 450 e-series
- 455 e-series Rancher
- 455 Rancher
- 460 Rancher
- 570
- 576 XP®
- 576 XP® AutoTune
- 576 XP® G
- 576 XP® W
- 576 XP® W AutoTune
- T435