Husqvarna: Ask & Answerpublic

Chainsaws

 
This is a public Forum  public

Posts

  • Ed Rezny
    "Adjustment Screw" for Husqvarna 316 Electric...escalated1
    Parts Question posted June 3, 2013 by Ed Rezny 
    Question:
    "Adjustment Screw" for Husqvarna 316 Electric chainsaw: The "adjustment screw" (as described in the manual's write-up below) on my 316 electric chainsaw snapped recently, but I cannot figure out the number of the part to order. The parts information I've seen online generally lists a number of screws that can be ordered, but not one specifically described below as the adjustment screw. Can you help me determine this? Thanks.

    "Seat the guide bar on the adjusting pin and replace the clutch cover. Check that the drive links fit correctly on the drive sprocket and that the chain is in the groove on the bar.
    Tighten bar nuts finger tight. Adjust chain tension, using
    combination wrench to turn adjustment screw clockwise to
    tighten. Tighten adjustment screw until the chain is drawn
    snugly against the underside of the bar."
  • Joey Joejoe
    16" bar for a 455 Rancher? I'd like to buy a...Answeredescalated1
    Parts Question posted February 11, 2012 by Joey Joejoe 
    Question:
    16" bar for a 455 Rancher?
    I'd like to buy a Rancher 455 20" saw as it looks like a reasonably priced saw that can handle a 20" bar. But at the same time I'd like to be able to switch to a smaller 16" bar when I don't need the 20" length. But I'm surprised that I can't seem to find a 16" bar for the 455. I would think (naively perhaps) that I could find a bar from 14 to 24" to easily fit most of these saws. Is that not true? If not true, why aren't these bars more interchangeable?

    Thanks
  • JP
    3120XP Ignition and carb question.escalated
    Parts Question posted January 9, 2014 by JP 
    Question:
    3120XP Ignition and carb question.
    Details:

    Based on the P/N of the carb (WG7) I would assume this is an EPA 3120XP? that is, if it was not put on at a later date than from the factory..

    The Number on the plate is
    965 96 07-00
    00 1600040

    I would assume that means year 2000 build and serial number of 1600040?

    with that being said, the P/N on the carb is a WG-7 which is the P/N of the EPA carb on the 2000 IPL.   It lists a WG-8 as the NON EPA carb part number.

    I also saw on my older 3120XP (its a 1989) it had a WG-2 (absolute garbage carb, would not run to save its life) and I upgraded it to a WG 8 or 10 (P/N: 503282001), i cant remember on that one.  The replacement carb fixed it and it runs awesome.  

    But the 1989 3120xp had a P/N of 503 13 85-01 for its ignition coil and my 2000 only has one P/N listed of 503 13 85-02 for the coil.  On my old saw the -01 was truly a non EPA chainsaw because it was not even available in a EPA version. But the 2000 i just got off ebay appears to be a tree hugger EPA model with the WG7 on it.

    My question is does it matter if i go to a WG8 or WG10 on this 2000 model and leave the 503 13 85-02 ignition on it?

    I really do not know why they would have a "EPA" and a "NON EPA" ignition on it. Does it not run as hot to create a spark not as hot as a NON EPA one?  

    I also noticed that I have seen several different HP ratings for the 3120xp. I have seen it listed as 9.2HP and as 8.4HP; both on husqvarna documentation.   Is that because the EPA is running at 8.4HP and the non runs at 9.2hp?

    any insight would be greatly appreciated.
     

     

     

    Photo:
  • Eugene Rounds
    338xpt Fuel tank vent valve PN number needed see image for...7
    Parts Question posted December 21, 2015 by Eugene RoundsAnswerArmy Diesel 
    Question:
    338xpt Fuel tank vent valve PN number needed see image for location.
    Details:

    338xpt Fuel tank vent valve PN number needed see image for location of the missing part. Not noted on the IPLs for some reason or I missing it.

     

  • Eric Groenendyk
    450 CHAIN OIL LEAK My 450 leaks out all it's chain oil...escalated6
    Parts Question posted July 3, 2014 by Eric Groenendyk 
    Question:
    450 CHAIN OIL LEAK
    My 450 leaks out all it's chain oil when stored. I saw a post from 2011 concerning a oil leak issue for a rancher 455 with similar issues as mine. The response listed parts to replace. Are the parts the same for the 450 & 455?
    Specifically the post listed #537 40 35 01 plug & #530 02 61 19 duck bill check valve. Are these the same for my 450?
  • keith olson
    460 Rancher replacement chain1
    Parts Question posted December 18, 2015 by keith olson 
    Question:
    460 Rancher replacement chain
    Details:

    What is the part number for a 24 inch replacement chain for the 460 rancher.  The manual give a part number of 503 30 79-84.  Nothing comes up when you do a search for this number. 

  • Bob Carden
    550XP Blown Transfer Port Gasket1
    Parts Question posted August 24, 2016 by Bob Carden 
    Question:
    550XP Blown Transfer Port Gasket
    Details:

    Can one of the mods hook me to a tech guy at Husky so I can get an answer to this?

    I need a transfer port gasket for a 550XP AT.

     

  • Ro Bo
    576xp crank bearings.escalated
    Parts Question posted June 3, 2013 by Ro Bo 
    Question:
    576xp crank bearings.
    Details:

    576xp crank bearings.

    What are the ball bearings size, the actual ball diameter and tolerance.

    Thanks.

  • Dave Rasmussen
    Are Chain Saw Models (Husqvarna) 450 and 450e the...Answeredescalated1
    Parts Question posted October 12, 2011 by Dave Rasmussen 
    Question:
    Are Chain Saw Models (Husqvarna) 450 and 450e the same saw but the 450 has a manual chain tension adjustment, but the 450e has a automatic chain tensioning design ? IAll other parts such as spark plugs, air filter and fuel filter are the same ? Is their a pdf type file listing Model 450 parts ? What type of Husqyarna 2 Cycle Oil should I use (the Premium synthetic blend with fuel stailizer/Low Smoke Formulatio or the XP Professional Performance 2 Cycle Oil ? Those two part numbers might be 578820100 and the other number might be your 578820086 !!!

    Thanks For Any Assistance
    Details:

     

    Are Chain Saw Models (Husqvarna) 450 and 450e the same saw but the 450 has a manual chain tension adjustment, but the 450e has a automatic chain tensioning design ?  IAll other parts such as spark plugs, air filter and fuel filter are the same ?  Is their a pdf type file listing Model 450 parts ?  What type of Husqyarna 2 Cycle Oil should I use (the Premium synthetic blend with fuel stailizer/Low Smoke Formulatio or the XP Professional Performance 2 Cycle Oil ? Those two part numbers might be 578820100 and the other number might be your 578820086 !!! 

    Thanks For Any Assistance

  • Richard Mulholland
    Based on your answer to my previous question concerning my...Answeredescalated1
    Parts Question posted December 1, 2011 by Richard Mulholland 
    Question:
    Based on your answer to my previous question concerning my 350 chainsaw with the following tag info,
    Husqvarna 350
    967 01 18-00
    S/N 05 0900904
    I began looking for the parts I need in the 350 (2005-05) manual. The parts that are shown in the illustrations show two different part numbers one for a 350 and one for a 350EPA. My saw has the heat deflection shield that is shown with only an EPA part number. This info begs the question; What parts do I purchase for my saw the ones with just the 350 designation or the ones with the 350EPA designation? I need an answer so I can order the correct parts. Thank you.

Filter by Type

Filter by Tag

Change View

Sort