Posts
General Product Question posted November 19, 2011 by David ParmeterQuestion:The trigger controlled steering on my 1830 EXLT is less than smooth. Sometimes the triggers are stuck and difficult to pull. Sometimes they seem totally in-effective, and I end up trying to steer it by pulling the handle bars left or right...and that's no easy task with this heavy machine. What gives?
D Scott
General Product Question posted January 22, 2016 by CHRIS VIGNOLAQuestion:Hello, I recently purchased an ST 227P snowblower with heated grips. Because of the lack of snow fall so far, I have not had to use the unit but one time but I am noticing that the heated grips don't seem to be heating the grips as they should with the switch in the "O" position. I ran it last night for at least 5 minutes just to be sure and they are definitely not getting warm. Any ideas on how I can troubleshoot this problem?
Thank you!
Mrvig- General Product Question posted December 31, 2012 by Eric HQuestion:I have a 4 year old Husqvarna 10530 SBE, and the "Traction Idler spring became disconnected and I cannot figure out where it hooks to. It was hanging off the Idler arm but I can't for the life of me see where it attaches. (fly wheel is removed)
There seems to be a hole in the body in the upper left but when I hook it there it just pops out.
Please Help !!!!!!!! - General Product Question posted February 29, 2016 by Shujun HuangQuestion:I bought Husqvarna Poulan PRO 5524ES snowblower in 2009. It is only being used for two seasons before. This year I used it for recent big snow storm. The oil leak was so bad after I used for more than 3 hours. I posted the problem and Eugene answered my question about how to take down the fly wheel in order to replace the oil seal. However, after I took down the fly wheel, I found out the leak was not from the oil seal at the shaft. It seems the leak was from the bottom of engine (from the rectangular hole at the bottom of engine). See the attached photos. Can anybody know where the leak actually coming from?
Shujun - General Product Question posted November 26, 2017 by Allen AndrewsQuestion:I need the dimensions on the following belts - looking for the width and length in inches
532 17 90-92-----traction drive V belt
AND
532 40 80-10-----impeller drive V belt - General Product Question posted January 17, 2015 by bob mccannQuestion:First time owner of a Husqvarna product. Last winter in the middle of one of Chicago's worst snow storms, my old one broke down and I had to scramble to find anything to blow snow. So I found the last one in the Chicago land area. I ordered it, it was shipped and arrived in a box a few days later. I read the quick start guide, and attached all the parts and such. I was snow blowing in an hour. Great. Now its a year later and went to the garage to start up my blower. Gas tank empty, checked oil, ok.
Looked for the fuel on/off switch? Looked for an on/off button. Looked for my paper work and could not find it. Looked for manufactures information number and such. Under a handle and some cables found a sticker. With the information on the sticker tried to find my snow blower online with the site. Bottom line, my machine has no on/off switch. My machine has no fuel on/off valve or switch. My machine has no engine throttle control. My machine is discontinued. My machine has a manual, but its in Spanish. My machine has a key switch, but the key does not turn!? My machine is not listed on the Husqvarna site. The Spanish manual has pictures of the machine, but it does not match the machine I own. The manuals offered online both on site and from manual sites, do not match my machine. The trouble shooting guide is for a machine with a key switch, a fuel valve and a throttle control. When I called and spoke to a customer service rep, she was clueless. The only help I have gotten is to take the machine into a dealer!? No manual I can read, no information online, no help with customer service rep. I feel I bought a lemon, so far its been not fun owning this machine. - General Product Question posted November 6, 2011 by GREG SKOWRONEKQuestion:New 924HV oil leak? I just got 924HV over a month ago, when i picked it up from the dealer the oil level was at full. I store it in the shed for over a month and today I saw (and smelled it too) a fairly large ( around 10 shoe size) paddle of oil underneath it. i tipped it to the side little bit and saw that there were few drops on the plastic cover underneath the thrower. However, i checked the oil level (few times today) and it is still on FULL, exactly as it was a month ago. Any ideas on whats going on?
I had it running for about 10 min after i purchased it to see if it works properly, everything was ok. - General Product Question posted December 20, 2016 by Gary EickenQuestion:I just purchased a new ST227P. Just wondering if the auger belt issue has been corrected.
- General Product Question posted November 2, 2016 by Kevin TurnerQuestion:How can you do a registration online if the drop down box is empty and will not allow you to up any information in the box? You have to have this to finish the registration.
Where Purchased is empty.
Why do they not have a support phone number? - General Product Question posted January 23, 2016 by James HixonQuestion:Just bought Husqvarna ST 224 snowthrower that was already put together by Lowes on Thursday and when I went to start it to test it out tonight before the big storm and it won't start. I tried electric and manual start nothing, new gas, theres oil in it I followed all the directions still nothing . Does anyone know what's wrong or if Im missing something?